What size electric motor do I need?

General rule of thumb: you need at least 2 lbs. of thrust for every 100 lbs. of fully-loaded boat weight (people and gear included). If things like wind or current are major factors where you fish, you’ll want a little extra thrust.

How do I know what size electric motor I need?

Divide the motor speed by the required speed and round down to get a starting gear ratio. Then divide the required torque by the gear ratio to find the newly required torque. This will help you narrow the choices down to a few select motors.

How do I choose an electric motor?

5 steps to choose the best motor for your application

  1. Step 1: Know the load characteristics. …
  2. Step 2: Get a handle on horsepower. …
  3. Step 3: Getting started. …
  4. Step 4: Adjust for duty cycle. …
  5. Step 5: The last consideration, motor hypoxia.

3.12.2011

How do you size a motor?

The required torque is calculated by multiplying the sum of load torque and acceleration torque by the safety factor. When the required torque for the motor varies over time, determine if the motor can be used by calculating the effective load torque.

IT IS INTERESTING:  Can a car engine run on hydrogen?

How do you size a 3 phase motor?

The NEC tables indicate that the full load current of a three-phase, 460 volt, 25 horsepower motor is 34 amps. Therefore, the conductors supplying the motor must be sized at 34 x 1.25 = 43A (125 % of 34 amps).

How do you size an electric motor for a pump?

The power required to drive the pump at the rated design condition should always be less than the nameplate horsepower rating of the motor. So if the pump will require 4.5 HP at the design condition, at a minimum, the motor should be sized for 5 HP – the next nominal size above 4.5 HP.

How does a simple electric motor work?

This simple electric motor works by the magnetic force F = IL x B. The magnetic field at both of these spots points in the same direction. … Thus, the magnetic force on the wire at opposite ends of the loop points in opposite directions, causing it to spin.

Which electric motor is best?

The BLDC motors are the most preferred motors for the electric vehicle application due to its traction characteristics. You can learn more about BLDC motors by comparing it with normal brushed motor. BLDC motors further have two types: i.

What is the difference between an electric motor and generator?

Converting energy from one form to another is the key to understanding the differences between electric motors and generators. An electric motor converts electricity into mechanical energy, providing a power source for machinery. A generator does the opposite of this, converting mechanical energy into electricity.

IT IS INTERESTING:  Frequent question: Can I claim car insurance for repairs?

What size breaker do I need for a 15 hp motor?

Full Load Current: Three Phase AC Motors

Motor Horsepower Size Breaker
7-1/2 230V 460V 40 30
10 230V 460V 50 30
15 230V 460V 70 40
20 230V 460V 100 50

How much weight can a 1 hp motor lift?

This means with 1 hp, you can lift about 550 lbs (250 kg) at a rate of 1 ft/sec, 1100 lbs at a rate of 0.5 ft/sec, 225 lb at a rate of 2 ft/sec, 1 lb at a rate of 550 ft/sec, and so on.

How do I know what size stepper motor I need?

Usually, you can choose a stepper motor by its size roughly. In general, when the torque is less than 0.8N.m, a stepper motor with a nema size of Nema 8-Nema 17 can be selected, when the torque is about 1~3N. m, Nema 23 stepper motor is more suitable. When the torque is more than 3N.

What size cable do I need for a 3 phase motor?

Size of Cable for Branch circuit which has Single Motor connection is 125% of Motor Full Load Current Capacity. Example: what is the minimum rating in amperes for Cables supplying 1 No of 5 hp, 415-volt, 3-phase motor at 0.8 Power Factor. Full-load currents for 5 hp = 7Amp. Min Capacity of Cable= (7X125%) =8.75 Amp.

What size breaker do I need for a 4 hp motor?

How to Calculate How What Size Circuit Breaker a Machine will Need:

HorsePower of Main Motor 220 Volts, 1 phase 220 Volts, 3 phase
1 Hp 5.6 Amps 2.8
2 11.2 5.6
3 16.8 8.4
4 22.4 11.2

What size breaker do I need for a 7.5 HP 3 phase motor?

You need 50 amp rated wire with a 50-100 amp breaker.

IT IS INTERESTING:  What does it mean when a motor has low compression?
Service station